Oxygen Probe Accessories

Download Reader Download Product Information Oxygen Probe Accessories                                      Armatures, fixtures and accessories for OxyGuard oxygen probes Accessories and Fixtures This brochure lists most of OxyGuard's large range of items helpful when installing and using the OxyGuard Standard Probe, the OxyGuard Model 420 or OxyGuard Model 840. A kit (junction box, spare cap with membrane, electrolyte etc) sufficient for installation and the first few years' use is shipped with every probe. Full information of items marked * is found on separate brochures. Some small improvements were made to probes in year 2000. The old type probes have two grooves in the thread between the top part and cap, the new type probes have four. New type probes do not have a large O-ring. Kits for old type probes (2 grooves on tread) - cap with membrane, O-ring, electrolyte, cleaning needle: Kits for new type probes (4 grooves on tread) - cap with membrane, O-ring, electrolyte, cleaning needle: D10ACPPMO - For ppm (mg/l) measurements. D10ACPPM - For ppm (mg/l) measurements. D10ACSATO - For % sat & % volume measurements D10ACSAT - For % sat & % volume measurements D10AC840O - For the Model 840 D10AC840 - For the Model 840 D10ACOILO - With oil proof membrane. D10ACOIL - With oil proof membrane. . . Caps for old type probes:. Caps for new type probes: D10CPPMO - Cap with ppm (mg/l) membrane. D10CPPM - Cap with ppm (mg/l) membrane. D10CSATO - Cap with % membrane. D10CSAT - Cap with % membrane. D10C840O - Cap for the Model 840 D10C840 - Cap for the Model 840 D10COILO - Cap with oil proof membrane. D10COIL - Cap with oil proof membrane. . . Sets of 25 membranes with small O-rings: . D10MPPM - Cap with ppm (mg/l) membrane. D10CB2 - 2-wire cable per meter. D10MSAT - Cap with % membrane. D10CB3 - 3-wire cable per meter. D10M840 - Cap for the Model 840 D10CB4 - 4-wire cable per meter. D10MOIL - Cap with oil proof membrane. D10CB5 - 5-wire cable per meter. . . D10AN1 - Anode for type 0 and type 1 probes. D10 JBX1 - Junction box for 1 probe. D10AN2 - Anode for type 2 probes D10JBX8 - Junction box for 8 probes. . . D10E0500 - 500 ml type 0 electrolyte. Measurement Chambers D10E01L - 1 l type 0 electrolyte. D10CHBP - By-pass (3/4" fittings). D10E1500 - 500 ml type 1 electrolyte. D10CHTP - 63/57 mm PVC T-piece D10E11L - 1 l type 1 electrolyte. . D10E2500 - 500 ml type 2 electrolyte. Probes Holders: D10E21L - 1 l type 2 electrolyte. D10HTH - With 3/4" pipe thread D10LOR - Large O-ring. D10HPI - For gluing onto 63/57 mm PVC pipe. . . . D10 DAT01 - DAT probe mount (complete). D10PP - Membrane protector. D10 DAT02 - Upper pipe for DAT. D10TOOL - Membrane ring removal tool. D10 DAT03 - Wall mount fitting for DAT. top Accessories and Fixtures The AirClean probe cleaning device uses compressed air* By-Pass measurement chamber with 3/4" hose connections The EasyCal permits calibration in two minutes!* The Probe Protector prevents the membrane from damage. Probe Holder for gluing onto standard 63/57 mm PVC piping Probe Holder with 3/4" pipe thread. Flange mount (has M18 thread). The Model 420 can also be flange mounted. The Pioneer mount, for use in activated sludge tanks, gives correct measurement and minimizes cleaning needs.* Mounting Plate 12 x 300 x 80 mm 3 mounting holes 10mm dia. distance between centers 130 mm. The DAT Probe Holder is ideal for many uses. The upper pipe is a 63/57 mm PVC pipe, standard length 1300 mm - other on request. Full-bore T-Piece flow-through measurement chamber AirAlarm ambient air measurement chamber.* The Renovation Tool is used to unscrew and replace the ring that holds the membrane. Flow- through gas measurement chamber.* Data subject to change without notice top